Features : Universal AC input / Full range (up to 305VAC) Built-in active PFC function High efficiency to 93.5% Protections: Short circuit / Over current / Over voltage / Over temperature OCP point adjustable through internal potentiometer / IP65 design for indoor or outdoor installations Suitable for dry / damp / wet locations 5 years warranty, Tc70 40000hrs
Blank : IP67 rated. Cable for I/O connection. : IP65 rated. Output constant current level can be adjusted through internal potentiometer. : IP67 rated. output constant current lever can be adjusted through output cable with 1-10V,PWM signal and Resistance E(option) : IP67 rated. Can be fixed by steel support.
SPECIFICATIONMODEL DC VOLTAGE RATED CURRENT RATED POWER OUTPUT 6.5A 156W CONSTANT CURRENT REGION 158.4W 300mVp-p
VOLTAGE TOLERANCE Note.3 �2.0% LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) EFFICIENCY (Typ.) INPUT AC CURRENT (Typ.) MAX.LED DRIVE NUMBER ON MCB C TYPE 16A INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER CURRENT PROTECTION OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & EMC WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY MTBF OTHERS
PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve) 115VAC 15units@230VAC COLD START 65A(twidth=425s measured at 50% Ipeak) ~ 108% Protection type : Constant current limiting, recovers automatically after fault condition is removed ~ 34V Protection type : Shut down o/p voltage with auto-recovery or re-power on to recovery 100�10 (RTH2) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down ~ +60 (Refer to "Derating Curve") 95% RH non-condensing 5G 12min./1cycle, period for 72min. each along Y, Z axes
I/P-O/P, I/P-FG, O/P-FG:100M Ohms 70% RH Compliance EN55015, EN61000-3-2 Class C (60% load) ; EN61000-3-3
Compliance EN61000-4-2,3,4,5,6,8,11, EN61547,light industry level (surge 4KV), criteria A 252.3Khrs min. MIL-HDBK-217F (25) Refer to mechanical specification DIMENSION 1.52Kg; 8pcs/13.16Kg/1.5CUFT PACKING 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured 20MHz of bandwidth by using a 12" twisted pair-wire terminated with & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Constant current operation region is within 60% ~100% rated output voltage, and the output power must be more than 60% rated output power. This is the suitable operation region for LED related applications, but please reconfirm special electrical requirements for some specific system design. 5. Derating may be needed under low input voltages. Please check the static characteristics for more details. 6. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time. 7. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
T case: Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point IP67 rated. Cable for I/O connection.
T case: Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point IP65 rated. Output constant current level can be adjusted through internal potentiometer.
T case: Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point IP67 rated. output constant current lever can be adjusted through output cable with 1-10V,PWM signal and Resistance
T case: Max. Case Temperature.(case temperature measured point) Ta: Ambient Temperature measured point
